Soal How To Do

1. Sitting on a bike, make sure you know where the bikes are and how to operate them
2. You have to learn to balance the bike. Find a person who can hold your bike behind you and try to go steady as you pedal it
3. Finally, you have to practice. Once you can balance, pedal, start, and stop, you are bicycle rider. Congratulation!
4. As you gain experience, raise the seat up so that only your toes can touch the ground while you are seated.
5. When you are ready, ride alone. But first, lower the seat until you can sit and put both feet flat on the ground
6. After practicing for a couple minutes, the person can release his or her hands while you try to keep your balance
1. Arrange these sentences below into a good order
A. 1 – 2 – 3 – 4 – 5 – 6
B. 1 – 2 – 4 – 5 – 6 – 3
C. 1 – 2 – 6 – 5 – 4 – 3
D. 1 – 2 – 5 – 3 – 6 – 4
E. 1 – 2 – 4 – 6 – 5 – 3

Burning a CD allows you to take music from one CD and transfer it onto another CD. This process is possible with any computer that has a CD driver, but it is easier on a computer that can run two CDs at once. Either way, you can copy all your music from one CD to the next. Here is how to copy from one CD to another, using one and two CD drivers.
Instructions Burning with two CD Trays
1. Insert the CD from which you want to burn music into your computer’s CD tray. Insert a blank CD into your computer’s second CD tray.
2. Open windows media player and wait for it to recognize the CD.
3. Click the “burn” option at the top of Windows Media Player. Drag the songs you want from the list of your songs into the area on the right labeled “Burn List”.
4. Choose the blank CD onto which you want to burn your song. This can be done at the top of the Burn List Menu.
5. Click the “Start Burn” button when you have all the song you want for the CD added to the Burn List. Wait for your computer to finish the CD, then take both of the CDs out.

2. What is the topic of the text?
A Running two CDs.
B. Opening Media Player.
C. Copying a compact disc.
D. Choosing the blank CD.
E. Inserting the CD into computer.

How to Clean a Blender

Cleaning a blender is easy, but it can be hard if you don't clean it immediately after you use it. Even if you don't have the time to clean it immediately after use, at least, pour in this simple cleaning the mixture to await your return later.

1)   Ensure that the blender jug is sitting on the base properly before proceeding.

2)   Fill the jug half full with warm water.

3)   Add one to two drops of dish-washing liquid; if you have a lemon, put in half a lemon, as the lemon rind will scrape off any particles and the juice and rind will eliminate odours.

4)   Place the lid on the blender.

5)   Plug the blender back into the electrical socket or switch the power point on.

6)   Press the low blend button and allow to blend for up to 30 seconds.

7)   Check that it has caught all the particles.

8)   Pour the liquid down the sink.

9)   Rinse under the faucet.

10)     Place upside down on a dish rack to dry.

3.  To make the cleaning process easy, it is suggested that we . . .

A. clean it twice a week.

B. wash it with warm water.

C. regularly clean it in the morning.

D. always clean it immediately after using.

4. We should . . . before turning on the blender.

A. pour the water down the sink

B. rinse it under the faucet

C. place the lid on

D. dry it

5. "Check that it has caught all the particles." (Step 7)

The underlined word refers to

A. the liquid in the blender

B. the lid of the blender

C. the faucet

D. the sink